Outback-power-systems MATE2 System Controller and Display Installation a Uživatelský manuál Strana 119
- Strana / 132
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
119
ADV/PASSWORD-------------
enter the password:
132
ENTER INC DEC EXIT
ADV/MATE/HBX------------
hbx-use 24.0 vdc
grid setpoint
DOWN ADV INC DEC
ADV----------------------------
choose device:
FX CC DC MATE
ADV/MATE/HBX------------
hbx-use 1.0 hrs
grid delay
DOWN ADV INC DEC
ADV/MATE/HBX------------
hbx-drop 26.0 vdc
grid setpoint
DOWN ADV INC DEC
ADV----------------------------
choose category:
HBX GRIDUSE AGS PG2
FLEXnet DC CHARGE
ADV/DC/CHARGE---------
return amps 10.4
DOWN INC DEC TOP
ADV/DC/CHARGE---------
battery voltage 26
DOWN INC DEC TOP
ADV/DC/CHARGE---------
charge factor 93 %
DOWN INC DEC TOP
ADV/DC/CHARGE---------
charge parameters
complete
TOP ADV MAIN
ADV----------------------------
choose device:
FX CC DC MATE
ADV/DC/PAGE1------------
choose category:
ADV BAT SHUNT PG2
ADV/DC/AUX/SOC HIGH
SOC high 90%
DOWN INC DEC TOP
ADV/DC/AUX/HIGH VOLT
high volts 29 vdc
DOWN INC DEC TOP
ADV/DC/AUX/HIGH VOLT
low volts 22.0 vdc
DOWN INC DEC TOP
ADV/DC/AUX/SOC LOW-
SOC low 59%
DOWN INC DEC TOP
ADV/DC/AUX/HI DELAY-
high setpoint delay
1 minutes
DOWN INC DEC TOP
ADV/DC/AUX/HI DELAY-
low setpoint delay
minutes
DOWN INC DEC TOP
ADV/DC/AUX/INVERT----
invert logic YES
DOWN YES NO TOP
ADV/DC/PAGE1------------
choose category:
ADV BAT SHUNT PG2
ADV/DC/PAGE2------------
choose category:
PG1 CHARGE AUX PG3
ADV/DC/PAGE3------------
choose category:
PG2 RESET CLR MAIN
ADV/DC/PAGE/RESET-----
reset DC to factory
defaults?
NO YES TOP
ADV/MATE/CLEAR--------
clear data log
memory?
YES NO TOP
ADV/DC/PAGE3------------
choose category:
PG2 RESET CLR MAIN
MATE HBX
MAIN--------------------------
6:54:42P
SUM STATUS SETUP ADV
ADV/SETTINGS/WARNING
changes made could
adversely eect
system performance
ADV/DC/PAGE3------------
choose category:
PG2 RESET CLR MAIN
ADV/DC/AUX------------
aux parameters
complete
TOP ADV MAIN
ADV----------------------------
choose device:
FX CC DC MATE
ADV/DC/PAGE2------------
choose category:
PG1 CHARGE AUX PG3
ADV/DC/AUX CONTROL--
currently MAN-OFF
DOWN OFF AUTO ON
ADV/DC/CHARGE---------
parameters met time
1 minutes
DOWN INC DEC TOP
ADV/DC/PAGE2------------
choose category:
PG1 CHARGE AUX PG3
- System Controller and Display 1
- Warranty 2
- Disclaimer 3
- Date and Revision 3
- Contact Information 3
- Contents 4
- MATE At a Glance 7
- OutBack MATE Functions 8
- MATE Specications 8
- What is a set point? 9
- Manual Setup 10
- Installation 10
- MATE2 Dimensions 11
- To Install the MATE: 11
- 1 Basic Operation 12
- Power Up 13
- MAIN Screen 15
- Navigation 16
- MATE Buttons 16
- How To Read a MATE Screen 17
- 2 MATE Setup 20
- Set Up the MATE 21
- Setting the Clock 22
- ADJUSTDATEANDTHENYEAR 23
- Contrast Adjustment 24
- Backlight Adjustment 25
- 3 MATE Summary Screens 27
- Summary Screen Overview 28
- FX Summary Screen 29
- Summary Screen Options 29
- 4 MATE Communications Options 33
- Communications Options 34
- Communication Errors 37
- Errors and Debugging 37
- 37
- 5 MATE Status Screens 39
- STATUS Screen Overview 40
- Reading a STATUS Screen 41
- FX STATUS MODE Screens 42
- FX STATUS METER Screens 43
- FX STATUS Batt(ery) Screens 44
- FX STATUS ERROR Screens 45
- FX STATUS WARN(ING) Screens 46
- FX DISCON(NECT) Screens 47
- 6 MATE Hot Keys 51
- INVERTER CONTROL 52
- Currently: ON 52
- AC IN Hot Key 53
- 1:35:04p 57
- SUM STATUS SETUP ADV 57
- 7 Advanced MATE Menus 58
- MATE Control Modes 59
- The ADVANCED Menus 60
- oat control 61
- FLEXnet DC* 62
- HBX Mode 63
- HBX Mode: 64
- HBX-Use Grid Delay 65
- HBX-Use Grid Set Point 65
- HBX-Drop Grid Set Point 66
- HBX-Drop Grid Delay 66
- AC Input Control 66
- Disable HBX 67
- AC INPUT CONTROL 68
- Currently:USE 68
- Grid-Use Mode 69
- Weekday Grid-Use Start 71
- Weekday Grid-Use Stop 72
- Weekend Grid-Use Start 73
- Weekend Grid-Use Stop 73
- AGS Setup 75
- AGS Port 76
- AGS Enabled 77
- DC Genset 78
- VDC Genstop 78
- GEN START CONTROL 80
- Weekday Start 81
- Weekday Stop 82
- Weekend Start 83
- Weekend Stop 84
- Voltage Start 85
- Load Start 86
- Load Start KW 87
- Load Start Delay 87
- Load Stop Delay 88
- Load Stop KW 88
- Must Run 89
- State of Charge 93
- Generator Exercise 96
- Ex Start Time 97
- Ex Period 98
- MATE DEFAULTS 99
- MATE ADVANCED Default Values 100
- • AGSQUIETTIMEMenu 101
- • AGSVOLTSTARTMenu 101
- • AGSLOADSTARTMenu 101
- • AGSTIMERSMenu 102
- • AGS%SOCMenu 102
- • AGSMUSTRUNMenu 102
- • AGSEXERCISEMenu 102
- AGS Start and Stop 103
- 8 MATE Menu Map 104
- Menu Structure 105
- MATE MENUS 109
- SETUP/MATE/PAGE1 114
- CLOCK CNT GLOW PG2 114
- SETUP/MATE/SUM/DELAY 114
- ADV/SETTINGS/WARNING 115
- ADV/FX/INVERTER— 115
- completed 115
- ADV/FX/GEN 116
- GEN programming 116
- completed 116
- 60 amp charge controller 117
- ADV/CC/ADVANCED-P01 118
- defaults? 118
- DOWN NO YES PORT 118
- ADV/PASSWORD 119
- enter the password: 119
- 132 119
- ENTER INC DEC EXIT 119
- ADV/MATE/AGS/MR 121
- end of MUST 121
- RUN menu 121
- ADV/MATE/AGS/FULLCHG 121
- MENUMAP 123
- OVERVIEW 123
- APPENDIX 125
- Further AGS settings: 126
- How to start my generator 126
- How to Stack FX Series 127
- Troubleshooting 128
- Page 122 129
- (YEAR) 129
- WARRANTY 130
- REGISTRATION 131
- Extended Warranty Application 131
Související produkty a manuály pro Nabíječky Outback-power-systems MATE2 System Controller and Display Installation a
(12 stránky)
(12 stránky)
(12 stránky)
Nabíječky Outback-power-systems FLEXpower ONE One Fully Pre-Wired Single Inverter Uživatelský manuál
(72 stránky)
(72 stránky)
Nabíječky Outback-power-systems AXS Card SunSpec Modbus Interface Installation Ins Uživatelský manuál
(2 stránky)
(2 stránky)
Nabíječky Outback-power-systems MATE2M System Controller and Display Installation Uživatelský manuál
(39 stránky)
(39 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce